Two Way Heat Dissipation 4-Wire PWM Fan Temperature Speed Controller Board US

Description

Free USPS First Class Shipping.
Note: This is a four-wire PWM fan controller can only control in line with Intel standard four-wire fan fan (12-48V majority of four-wire fan support), can not control the 2-3 line fan, can not be completely shut off fan.
Although the controller can work between 8-60V, the actual power supply voltage must match the fan operating voltage. For example, to control the 12V fan, it must be powered by 12V. The wrong selection of the power supply may burn the fan and damage the control panel at the same time! !
Specifications:
1.Operating voltage: DC8-60V (must be equal to the fan voltage, 12V fan, but if you use 24V power supply fan will burn)
2.Current: Dashboard Working current 35mA (12V) 22mA (24V)
3.Control: not fan the current limit, but the board fan connector pins do not exceed 4.the maximum 3A current, use more current fan set the fan power cable is connected directly to the mains!
5.Control Output range: 10% -100% (this is the signal output range, the situation depends on the fan performance)
6.Temperature Probe Specifications: NTC 10K B = 3950
7.Temperature measurement: -9.9 ℃ to 70.1 ℃ error <1 ℃ (use 1% precision probe)
8.Temperature range temperature zone: accelerating temperature 0-60 ℃, full temperature 10-70 ℃
9.Speed measurement: 10-9990 rpm, more than is always displayed maximum resolution of 10 rpm, display units * 10 rpm (speed measurement according to the most common 2-pole signal fan design, the vast majority of fans are 2 pole signal)
10.Stall warning speed: less than 375rpm
Wiring instructions:
Blue screw terminal connections the mains (power supply voltage equivalent to the fan voltage use, and in the 8-60V range), please note not to take the wrong polarity; "Channel 1" and "Channel 2" two 4P socket connection fan, power supply line sequence is negative, positive power, speed feedback, PWM control (for details, see wiring diagram below); "thermal 1" and "2 thermal" Connect NTC thermistor (parameter 10K B = 3950) , respectively, with two channels of temperature control temperature fan; "beep" jacks AC buzzer, when you turn the alarm stops, the fan will stop the buzzer sounding.
Wiring Note:
The maximum allowable current single fan interface is 3A, if you need to control the higher current fan, set the fan power cord directly connected to the main power supply of the above (and fan controller capability independent of current, but to consider the power conductors current capacity)
Display Description:
Dashboard via digital display value, the right of the four LED digital tube digital tube current value indicates the meaning of the first line of each table led two temperature channels and a rotational speed (x10rpm), the two led the second line of distinguished representatives channel two of temperature and speed (x10rpm). Under normal operating conditions will follow the order of the four values ??displayed in turn, may at any time by pressing the "+" "-" button to quickly switch to manual values ??manually switch will stay at this value for a long time re-entering the round was state . It can be masked as required channel II display.
Setting Note:
1.Under setting state. Speed ??and temperature zones, if more than 15 seconds is not operated, the automatic exit without saving the data.
2.When the set temperature zone, full temperature must be higher than the same channel accelerated temperature of at least 5 degrees Celsius, a temperature value when setting causes this condition is not met, the controller will automatically adjust the temperature data to ensure compliance with the other difference is not low in conditions of 5 degrees Celsius, this is automatically adjusted to a one-way, and if you need to manually adjust the callback another temperature.
3.Channel two masked display settings only affect working state data show that two of the control channel and parameter settings are not affected, the normal work.
Package Included:
1x 4-Wire Temperature Control PWM Computer Fan Speed Controller
2x 1 meter temperature probe
1x Diameter 12mm length 10cm buzzer
Payment
1. We accept PAYPAL only.
2. Payment must be made within 7 days of auction closing (Unpaid dispute will automatically open when item
is not paid in 7 days).
3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
4. Please list your special requests (color, packages, value of declaration, etc.) in the EBAY NOTES SECTION
when you make payment
We offer USPS First Class Shipping / Not Ecomomy
- There is a big difference between USPS First Class Shipping and Economy Shipping
- Our orders are shipped every day and delivered within 3-8 days
Returns Policy
1. Customer satisfaction is our top goal. All products are quality checked. They are new and in good condition when shipped to our customers. If product is defective or damage upon arrival, or wrong product shipped, please keep in touch with us immediately. Returns accepted within 14 days of delivery date
and item must be in original new condition, not worn or altered in any way with attached tags & wrap.Otherwise deal is final. Return shipping must be paid by buyer.
2. Please keep in touch with us first if you have anyproblems/questions/concerns. We will be happy to resolve
any issues you may have in a cordial and friendly manner.
3. We appreciate your Positive Feedback, and will do the same in return. PLEASE DO NOT leave negative feedback without first communication with us. Please allow max 24 HOURS for us to respond
About Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is
very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or
negative feedback, so that we can satisfactorily address your concerns.It is impossible to address
issues if we do not know about them!