DC5-12V 1A 2-3 wire Fan Speed Controller with Knob Switch Fan Speed Control off

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
DC5-12V 1A 2-3 wire Fan Speed Controller with Knob Switch Fan Speed Control off
Popular
Popular
Product Introduction
Product Feature:
1. Smooth DC output, good control effect
2. With switch, can be shut down
3. Product appearance is exquisite
4. The starting speed can be adjusted, and the use effect is good
5. Simple and convenient operation
Product parameters:
Working voltage: DC5-12V (DC4.7-14V)
Fan current: 0.1-1A Fan current is lower than 0.1A Control effect is slightly poor, more than 1A may damage the circuit board
Self loss, not connected to fan, less than 30mA
Start position adjustment range: 0% - 60% (internal circuit control parameters)
Input interface model: red and black line input/2510-3P terminal input optional
Output interface model: 2510-3P, spacing 2.54mm, conventional CPU, chassis fan socket
Function description:
Pay attention to the positive and negative poles and the power supply voltage (reverse connection will damage the board). After the power supply and fan are connected, they can be used. The potentiometer is closed anticlockwise to the end, and clockwise to the end is the maximum output
The separate small adjustable resistor (initial speed adjustment) on the board is used to adjust the speed of the just opened position. The input of the speed signal port is directly connected with the fan output. It is mainly used to lead the fan speed signal back to the main board of the device to detect the speed. There is no connection with the circuit of the controller
matters needing attention:
Do not control fans over 1A, do not connect the wrong or reverse power supply, and do a good job of insulation to avoid output short circuit
Shipping list:
Speed control module X1
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
DC5-12V 1A 2-3 wire Fan Speed Controller with Knob Switch Fan Speed Control off
Product Introduction
Product Feature:
1. Smooth DC output, good control effect
2. With switch, can be shut down
3. Product appearance is exquisite
4. The starting speed can be adjusted, and the use effect is good
5. Simple and convenient operation
Product parameters:
Working voltage: DC5-12V (DC4.7-14V)
Fan current: 0.1-1A Fan current is lower than 0.1A Control effect is slightly poor, more than 1A may damage the circuit board
Self loss, not connected to fan, less than 30mA
Start position adjustment range: 0% - 60% (internal circuit control parameters)
Input interface model: red and black line input/2510-3P terminal input optional
Output interface model: 2510-3P, spacing 2.54mm, conventional CPU, chassis fan socket
Function description:
Pay attention to the positive and negative poles and the power supply voltage (reverse connection will damage the board). After the power supply and fan are connected, they can be used. The potentiometer is closed anticlockwise to the end, and clockwise to the end is the maximum output
The separate small adjustable resistor (initial speed adjustment) on the board is used to adjust the speed of the just opened position. The input of the speed signal port is directly connected with the fan output. It is mainly used to lead the fan speed signal back to the main board of the device to detect the speed. There is no connection with the circuit of the controller
matters needing attention:
Do not control fans over 1A, do not connect the wrong or reverse power supply, and do a good job of insulation to avoid output short circuit
Shipping list:
Speed control module X1
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.