9536 KB Electronics 1HP/0.75kW Digital AC Inverter/Drive with CSP, KBDA-24D

Description

9536 KB Electronics 1HP/0.75kW Digital AC Inverter/Drive with CSP, Gray, 115/208-230VAC Single Phase Input, 230VAC 3-Phase 3.6 Amp Output
Ratings
Manufacturer
KB Electronics (Nidec)
Part Number
9536
Model Number
KBDA-24D
AC Line Input
115/208-230 VAC
Single Phase
50/60Hz
Maximum Input Current
14 Amps @ 115VAC
8.1 Amps @ 208/230VAC
Fuse/Circuit Breaker Rating
20 Amps @ 115VAC
15 Amps @ 208/230VAC
Output Voltage
0-230VAC
Max Output Power
1 HP
0.75 kW
3.6 Amps
Net Weight
5.9 lbs
2.7 kg
Case
A
5.51" (140mm) Width x 9.53" (242mm) Height x 5.86" (149mm) Depth
Gray
Rugged Die-Cast Aluminum
NEMA 4X / IP65 Washdown /Watertight Indoor/Outdoor
Warranty
18 Month Limited Warranty
Specifications
Voltage Operating Range
115 VAC +/-15%
208 VAC -15% / 230VAC +15%
Maximum Load (of Current Overload for 2 Minutes)
150 %
Starting Torque
200 %
Switching Frequency
8, 10 or 12 kHz
Signal Following Input Voltage Range
0-5 VDC
Output Frequency Resolution
10 Bits
0.06 Hz
Minimum Operating Frequency at Motor
0.3 Hz
Acceleration Time
0.1 to 180.0 Seconds
Deceleration Time
0.3 to 180.0 Seconds
Speed Range
60:1 Ratio
Speed Regulation (30:1 Speed Range, 0 – Full Load)
2.5 % of Base Speed
Overload Protector Trip Time for Stalled Motor
6 Seconds
Undervoltage/Overvoltage Trip Points
76/141VAC @ 115VAC Input
151/282VAC @ 208/230VAC Input
Run/Fault Output Relay Contact Rating
1 Amp @ 30VDC
0.5 Amp @ 125VAC
0.25 Amp @ 250VAC
Braking
Regenerative (DC Injection Braking)
Operating Temperature
0-45°C
32-113°F
Storage Temperature
-25 to 85°C
-13 to 185°F
Benefits
Saves Time
Easy to Install and Simple to Operate. Does not require commissioning.
With CSP™ you are up and running in less than 10 minutes.
Motors Last Longer
Proprietary CL Software
Provides overload protection, prevents motor burnout and eliminates nuisance tripping. UL approved as electronic overload protector for motors.
Energy Saving
Uses only the power the application requires. Replacing constant speed with variable speed will significantly reduce energy costs.
Customization for OEM’s
When an off the shelf drive does not meet your needs, KB will work with you to provide a custom drive solution, Ready to Use, “Out-of-the-Box.”
Customization includes: Pre-calibrating or programming of a stock control, adding a custom label or branding, custom software, PLC functions or designing a new control.
GFCI Compatible
Allows equipment to operate with Ground Fault Circuit Interruption circuit breakers or outlets
Additional Features
Sensorless Flux Vector Control:
Flux Vector Compensation with Static Auto-Tune provides excellent speed regulation with high torque loads throughout the entire speed range. Auto energy saving at light loads. Smooth motor torque.
Electronic Inrush Current Limit (EICL™) Protection:
Eliminates harmful inrush AC line current during power up.
Multi-Function Output Relay:
Can be used to turn equipment on or off, to signal a warning if the drive is put into “Stop” mode, or to signal if a fault has occurred.
Jog-Local/Remote:
Set the drive to Jog Mode or changes between Local (Keypad) or Remote Operation
Built-in Potentiometer:
Quickest way to change motor speed.
Ride-Through:
Provides smooth recovery to the previous set speed during a momentary power loss.
Holding Torque at Zero Speed:
Resists motor shaft rotation when the drive is in “Stop” mode
Regeneration Protection:
Eliminates tripping due to high bus voltage caused by rapid deceleration of high inertial loads.
Undervoltage and Overvoltage Protection:
Shuts down the drive if the AC line input voltage goes above or below the operating range.
Short Circuit Protection:
Shuts down the drive if a short circuit occurs at the motor (phase-to-phase).
Applications
Actuators
Air Cleaners
Amusement Rides
Ball Pitching Machines
Blowers
Boat Lifts
Bowling Alley Lane Cleaners
CNC
Conveyors
Door & Gate Openers
Drilling
Duct Cleaners
Dumbwaiters
Elevators and Hoists
Exercise Equipment
Fabric Processing
Fans
Food Processing
Garment Cutting
Grinding and Polishing
Hoppers
Horse Walkers
HVAC
Indexers
Irrigation
Laminating
Lift Station Pumps
Machine Tools
Medical
Milling
Mixers
Oven Conveyors
Packaging
Paint Blenders, Shakers, and Sprayers
Paper Handling
Portable Equipment Used with GFCIs
Pottery Wheels
Printing
Pumps
Range Hoods
Sandblasting
Saws
Sewing
Stretch Wrap
Textile
Treadmills
Wave Soldering
Web Processing
Wheelchair Lifts
Whole House Vacuums and Attic Fans
Wire Feeders
Wood and Metal Lathes and Cutters
Winders and Unwinders
Drive Options
IODA Input/Output Multi-Function Board:
Adds up to 17 points of additional I/O.
Modbus Serial Communication Module:
See instruction manual for complete description.
Drive-Link™ Programming Kit:
Allows PC programming.
On/Off AC Line Switch:
Disconnects the AC line.
Class “A” (CE) RFI Filter:
Installs inside the drive.
Liquidtight Fittings:
Provides a liquid-tight seal for wiring the drive. Kit includes necessary liquidtight fittings.